Q-Seal 290S Detector Loop Sealant

Chemque's Q-Seal Polyurethane 290S Sealant is primarily used to seal traffic detector wire loops like the Marsh Products Preformed Saw-Cut Loops in channels cut into asphalt or concrete. It requires no mixing, can be applied in winter or summer, and protects the wire loop from contact with water, oil or other chemicals. The 30-ounce tube fits in a manual or air-operated caulk gun and will seal two 4-foot-by-6-foot loops.

This Marsh Preformed Saw-Cut Loop consists of multiple turns of wire, bundled together to form a 1.5-foot-by-4.5-foot loop. It comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

The loop is intended to be used when pavement has already been installed. A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel. If you need sealant to close up the channel, see our Preformed Saw-Cut Loop Kits, which include the wire and one or two tubes of sealant, depending upon the size of the loop.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This Marsh Preformed Saw-Cut Loop consists of multiple turns of wire, bundled together to form a 2-foot-by-6-foot loop. It comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

The loop is intended to be used when pavement has already been installed. A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel. If you need sealant to close up the channel, see our Preformed Saw-Cut Loop Kits, which include the wire and one or two tubes of sealant, depending upon the size of the loop.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This Marsh Preformed Saw-Cut Loop consists of multiple turns of wire, bundled together to form a 2.5-foot-by-6-foot loop. It comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

The loop is intended to be used when pavement has already been installed. A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel. If you need sealant to close up the channel, see our Preformed Saw-Cut Loop Kits, which include the wire and one or two tubes of sealant, depending upon the size of the loop.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This Marsh Preformed Saw-Cut Loop consists of multiple turns of wire, bundled together to form a 3-foot-by-6-foot loop. It comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

The loop is intended to be used when pavement has already been installed. A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel. If you need sealant to close up the channel, see our Preformed Saw-Cut Loop Kits, which include the wire and one or two tubes of sealant, depending upon the size of the loop.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This Marsh Preformed Saw-Cut Loop consists of multiple turns of wire, bundled together to form a 4-foot-by-6-foot loop. It comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

The loop is intended to be used when pavement has already been installed. A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel. If you need sealant to close up the channel, see our Preformed Saw-Cut Loop Kits, which include the wire and one or two tubes of sealant, depending upon the size of the loop.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This Marsh Preformed Saw-Cut Loop consists of multiple turns of wire, bundled together to form a 4-foot-by-7-foot loop. It comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

The loop is intended to be used when pavement has already been installed. A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel. If you need sealant to close up the channel, see our Preformed Saw-Cut Loop Kits, which include the wire and one or two tubes of sealant, depending upon the size of the loop.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This Marsh Preformed Saw-Cut Loop consists of multiple turns of wire, bundled together to form a 4-foot-by-8-foot loop. It comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

The loop is intended to be used when pavement has already been installed. A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel. If you need sealant to close up the channel, see our Preformed Saw-Cut Loop Kits, which include the wire and one or two tubes of sealant, depending upon the size of the loop.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This Marsh Preformed Saw-Cut Loop consists of multiple turns of wire, bundled together to form a 4-foot-by-9-foot loop. It comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

The loop is intended to be used when pavement has already been installed. A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel. If you need sealant to close up the channel, see our Preformed Saw-Cut Loop Kits, which include the wire and one or two tubes of sealant, depending upon the size of the loop.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This Marsh Preformed Saw-Cut Loop consists of multiple turns of wire, bundled together to form a 4-foot-by-10-foot loop. It comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

The loop is intended to be used when pavement has already been installed. A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel. If you need sealant to close up the channel, see our Preformed Saw-Cut Loop Kits, which include the wire and one or two tubes of sealant, depending upon the size of the loop.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This Marsh Preformed Saw-Cut Loop consists of multiple turns of wire, bundled together to form a 4-foot-by-11-foot loop. It comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

The loop is intended to be used when pavement has already been installed. A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel. If you need sealant to close up the channel, see our Preformed Saw-Cut Loop Kits, which include the wire and one or two tubes of sealant, depending upon the size of the loop.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This 100-foot #16 awg cable is used to extend the distance between a loop and a vehicle detector. (For other lengths, please contact us.)

This Marsh Preformed Saw-Cut Loop consists of multiple turns of wire, bundled together to form a 4-foot-by-12-foot loop. It comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

The loop is intended to be used when pavement has already been installed. A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel. If you need sealant to close up the channel, see our Preformed Saw-Cut Loop Kits, which include the wire and one or two tubes of sealant, depending upon the size of the loop.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

The 1.5-foot-by-4.5-foot Marsh Preformed Direct Burial Loop comes with four choices of lead-in length. It is designed for on-site installation prior to pouring pavement material.

Each loop consists of multiple turns of wire, bundled together, with the narrow ends encased in PVC tubing to ensure easier installation.

The loops are ideally suited for vehicle detection in traffic control environments such as drive-thrus or parking lots when connected to the Marsh Products 610 Loop Vehicle Detector. They are also compatible with other brands of vehicle detectors.

The loop is intended to be used before pavement installation; if pavement has already been poured, the Marsh Products Preformed Saw-Cut Loop Kit is more cost-effective and easier to install.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

Marsh Products' 867 Saw-Cut Vehicle Detector Loop Kit consists of 85 feet of #16 awg wire and loop sealant for the installation of a five-turn loop.

It is ideally suited for vehicle detection in traffic control environments such as drive-thrus or parking lots when connected to the Marsh Products 610 Loop Vehicle Detector.

The 2-foot-by-6-foot Marsh Preformed Direct Burial Loop comes with four choices of lead-in length. It is designed for on-site installation prior to pouring pavement material.

Each loop consists of multiple turns of wire, bundled together, with the narrow ends encased in PVC tubing to ensure easier installation.

The loops are ideally suited for vehicle detection in traffic control environments such as drive-thrus or parking lots when connected to the Marsh Products 610 Loop Vehicle Detector. They are also compatible with other brands of vehicle detectors.

The loop is intended to be used before pavement installation; if pavement has already been poured, the Marsh Products Preformed Saw-Cut Loop Kit is more cost-effective and easier to install.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

The 2.5-foot-by-6-foot Marsh Preformed Direct Burial Loop comes with four choices of lead-in length. It is designed for on-site installation prior to pouring pavement material.

Each loop consists of multiple turns of wire, bundled together, with the narrow ends encased in PVC tubing to ensure easier installation.

The loops are ideally suited for vehicle detection in traffic control environments such as drive-thrus or parking lots when connected to the Marsh Products 610 Loop Vehicle Detector. They are also compatible with other brands of vehicle detectors.

The loop is intended to be used before pavement installation; if pavement has already been poured, the Marsh Products Preformed Saw-Cut Loop Kit is more cost-effective and easier to install.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

The 3-foot-by-6-foot Marsh Preformed Direct Burial Loop comes with four choices of lead-in length. It is designed for on-site installation prior to pouring pavement material.

Each loop consists of multiple turns of wire, bundled together, with the narrow ends encased in PVC tubing to ensure easier installation.

The loops are ideally suited for vehicle detection in traffic control environments such as drive-thrus or parking lots when connected to the Marsh Products 610 Loop Vehicle Detector. They are also compatible with other brands of vehicle detectors.

The loop is intended to be used before pavement installation; if pavement has already been poured, the Marsh Products Preformed Saw-Cut Loop Kit is more cost-effective and easier to install.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This speaker is a replacement for the remote speaker that comes with our Alpha Series Single-Channel Voice Communication System. It is designed for surface mounting only and does not include cable.

The 4-foot-by-6-foot Marsh Preformed Direct Burial Loop comes with four choices of lead-in length. It is designed for on-site installation prior to pouring pavement material.

Each loop consists of multiple turns of wire, bundled together, with the narrow ends encased in PVC tubing to ensure easier installation.

The loops are ideally suited for vehicle detection in traffic control environments such as drive-thrus or parking lots when connected to the Marsh Products 610 Loop Vehicle Detector. They are also compatible with other brands of vehicle detectors.

The loop is intended to be used before pavement installation; if pavement has already been poured, the Marsh Products Preformed Saw-Cut Loop Kit is more cost-effective and easier to install.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

The 4-foot-by-7-foot Marsh Preformed Direct Burial Loop comes with four choices of lead-in length. It is designed for on-site installation prior to pouring pavement material.

Each loop consists of multiple turns of wire, bundled together, with the narrow ends encased in PVC tubing to ensure easier installation.

The loops are ideally suited for vehicle detection in traffic control environments such as drive-thrus or parking lots when connected to the Marsh Products 610 Loop Vehicle Detector. They are also compatible with other brands of vehicle detectors.

The loop is intended to be used before pavement installation; if pavement has already been poured, the Marsh Products Preformed Saw-Cut Loop Kit is more cost-effective and easier to install.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

The 853 Air Hose Vehicle Detector is a low-cost, easy-to-install vehicle detection alternative for low-traffic applications. Simply attach the 10-foot air hose to the air switch enclosure at one end, lay the hose across the driving lane and fasten the hose detector at the other end.

The air pressure switch is packaged in a weather-resistant metal housing that can be mounted to a flat surface.

The 4-foot-by-8-foot Marsh Preformed Direct Burial Loop comes with four choices of lead-in length. It is designed for on-site installation prior to pouring pavement material.

Each loop consists of multiple turns of wire, bundled together, with the narrow ends encased in PVC tubing to ensure easier installation.

The loops are ideally suited for vehicle detection in traffic control environments such as drive-thrus or parking lots when connected to the Marsh Products 610 Loop Vehicle Detector. They are also compatible with other brands of vehicle detectors.

The loop is intended to be used before pavement installation; if pavement has already been poured, the Marsh Products Preformed Saw-Cut Loop Kit is more cost-effective and easier to install.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

The 4-foot-by-9-foot Marsh Preformed Direct Burial Loop comes with four choices of lead-in length. It is designed for on-site installation prior to pouring pavement material.

Each loop consists of multiple turns of wire, bundled together, with the narrow ends encased in PVC tubing to ensure easier installation.

The loops are ideally suited for vehicle detection in traffic control environments such as drive-thrus or parking lots when connected to the Marsh Products 610 Loop Vehicle Detector. They are also compatible with other brands of vehicle detectors.

The loop is intended to be used before pavement installation; if pavement has already been poured, the Marsh Products Preformed Saw-Cut Loop Kit is more cost-effective and easier to install.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

The 4-foot-by-10-foot Marsh Preformed Direct Burial Loop comes with four choices of lead-in length. It is designed for on-site installation prior to pouring pavement material.

Each loop consists of multiple turns of wire, bundled together, with the narrow ends encased in PVC tubing to ensure easier installation.

The loops are ideally suited for vehicle detection in traffic control environments such as drive-thrus or parking lots when connected to the Marsh Products 610 Loop Vehicle Detector. They are also compatible with other brands of vehicle detectors.

The loop is intended to be used before pavement installation; if pavement has already been poured, the Marsh Products Preformed Saw-Cut Loop Kit is more cost-effective and easier to install.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This Marsh Preformed Saw-Cut Loop Kit consists of multiple turns of wire, bundled together to form a 1.5-foot-by-4.5-foot easy-to-install loop. Also included is a tube of polyurethane loop sealant to close up the channel cut in the pavement for the loop. The loop comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel, and the sealant is applied with a caulk gun.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

Note: If you're purchasing more than one of this product and you want expedited shipping, please contact us at sales@MarshProducts.com or 630-879-8008 for additional savings on your freight costs.

The five-turn, PVC-encased, Model 865C Preformed Loop is designed for on-site installation prior to pouring pavement material. The 865 Preformed Loop is ideally suited for drive-thru applications when used in conjunction with the Marsh 610 Loop Vehicle Detector. Because it is self-contained, the 865 Preformed Loop greatly reduces installation time.

This Marsh Preformed Saw-Cut Loop Kit consists of multiple turns of wire, bundled together to form a 2-foot-by-6-foot easy-to-install loop. Also included is a tube of polyurethane loop sealant to close up the channel cut in the pavement for the loop. The loop comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel, and the sealant is applied with a caulk gun.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

This Marsh Preformed Saw-Cut Loop Kit consists of multiple turns of wire, bundled together to form a 2.5-foot-by-6-foot easy-to-install loop. Also included is a tube of polyurethane loop sealant to close up the channel cut in the pavement for the loop. The loop comes with a standard 20-foot lead-in; lead-ins of up to 100 feet are available.

A concrete saw is used to cut a rectangular pattern in the concrete or asphalt. The one-piece loop is set into the channel, and the sealant is applied with a caulk gun.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.

The 4-foot-by-11-foot Marsh Preformed Direct Burial Loop comes with four choices of lead-in length. It is designed for on-site installation prior to pouring pavement material.

Each loop consists of multiple turns of wire, bundled together, with the narrow ends encased in PVC tubing to ensure easier installation.

The loops are ideally suited for vehicle detection in traffic control environments such as drive-thrus or parking lots when connected to the Marsh Products 610 Loop Vehicle Detector. They are also compatible with other brands of vehicle detectors.

The loop is intended to be used before pavement installation; if pavement has already been poured, the Marsh Products Preformed Saw-Cut Loop Kit is more cost-effective and easier to install.

The standard lead-in length is 20 feet; if you want a longer lead-in, use the drop-down menu to specify the length you desire.